Conquer your everyday with the SERIES-S22 from JAC Vapour. With its all-day battery life, tough construction and compact design, this is an electronic cigarette designed to keep up with you, from the morning commute right through till bedtime. Ideal for new vapers, its simplicity will help you hit the ground running, while also retaining the flexibility and power more experience vapers demand.
S22 Series Battery
With massive battery life of 2600mah, the SERIES-S22 will keep up with all day vaping needs.
How long to charge: 4 hours.
Battery Size: 2600mAh
Charge indication: Green LED Indicates Above (70%+)
Blue LED Indicates Between (30-70%)
Red LED Indicates RECHARGE (Less Than 30%)
Flashing Red Light Battery drained.
S22 Series Tank
If you loved the original S22 tank, we’ve got a treat for you – the new and improved S22 topfill. Bringing all of the fantastic performance, design and build quality of the original, this updated model also adds the joys of topfill, making it easier to keep topped up throughout the day. Available in black, or green, it’s ready for work and play. Plus, it shares its predecessor’s flexibility, supporting both mouth to lung and direct lung vaping with the change of a coil.
Set up procedure
The device is sub-ohm compatible and when you are ready to experiment you can upgrade to the DL coil at 1.0 Ω or 0.5 Ω. The lowest resistance coil the device can be used with is 0.5 Ω.
Using the device; Make sure to charge the battery before use as some batteries may not be fully charged out of the box. Follow figs.1-8 for full set up instructions. After filling your tank a new coil may flood due to priming or, a few times, as it beds in. This can cause gurgling or a bit of leakage from the airflow. To clear this hold the device (like a fishing rod) and flick (fig. 8) down sharply (in a whipping motion) a few times, this will clear any excess liquid and prevent gurgling and leaking.
Finger-tight only: The SERIES-S22 is a precision engineered device, so you don’t need to be He-Man when tightening parts, finger-tight is enough for all threads overtightening may cause damage.
If you're experiencing a leak or gurgling/spitting from your SERIES-S tank, there may be a number of different reasons. The first step is to identify where the leak is coming from:
- Mouth tip - Normally a sign that the coil is flooded.
- Base - Normally a sign that the coil is flooded, the coil is loose, or the tank is losing pressure
- Tank housing - Possibly a sign that there is a physical fault with the tank housing (i.e. a crack)
A leaking or gurgling tank is almost always a symptom of a flooded coil, however.
Flooding occurs when an excess of e-liquid is pulled into the coil and begins to leak out into the airflow or up the tank chimney and out of the mouthpiece. It's almost always accompanied by a distinct gurgling sound.
Flooding can occur for a few different reasons:
1. TYPE OF E-LIQUID
The type of e-liquid used can have an effect in rare cases. Using a thin e-liquid that's high in PG in a direct lung setup which typically will be designed to rewick more quickly can occasionally lead to flooding, though this is fairly uncommon. Many vapers can use High PG e-liquids quite happily in a direct lung tank or device without issue.
Far more commonly, flooding can occur due to the way the device is being used. Taking lots of long, deep draws in quick succession has the effect of pulling too much e-liquid into the atomising chamber. The coil will have difficulty vaporising it all, with the excess beginning to leak as described above.
Similarly, taking lots of shallow puffs can achieve a similar effect, as the coil doesn't always have the time to get up to operating temperature.
To really get the most from your vaping experience, you should be aiming for relaxed draws, 3-5 seconds in length. You should also try to avoid inhaling while the button isn't pushed down, as that will lead to more e-liquid being pulled into the coil while is not operating.
3. BEING LEFT TO SIT
Finally, leaving a tank full of e-liquid to sit for extended periods can cause the coil to flood over time. The wicking material is pretty good at only absorbing the e-liquid it needs, and the pressure inside the tank helps hold the e-liquid in place, but given enough time it can become oversaturated. If you find yourself leaving your tank unused for long periods, it's possible that you may run into a flooded coil from time to time.
How to Fix a Flooded Coil
So, taking the advice above on board, if you do encounter a flooded coil, there are some simple steps you can take to resolve things.
The flick method is a good starting point. Holding the device in your hand, flick down sharply a few times. This will help pull the liquid up through the chimney and out the mouth tip, so you may need to dry this off with some tissue paper before using your device again.
If the flick method doesn't resolve the issue, it's possibly a sign that the coil needs to be replaced. Over time the wicking material will begin to clog, limiting its ability to absorb and hold e-liquid. Typically most coils should last for around 7-10 refills before they'll need to be replaced, so we'd recommend trying a fresh coil and following the advice laid out above.
LEAKING FROM THE BASE
Leaking from the base is normally a sign that the coil is flooded (see above), or that the coil is loose/cross threaded.
If you've followed the steps above to avoid or fix a flooded coil, you should next check to make sure that your coil is firmly screwed into place, and hasn't been crossthreaded. This is a particularly easy thing to miss, but it's always worth double checking as it's a simple solution that helps to resolve things in many cases. Coils should be screwed in tight enough to catch (finger tight), but you should avoid over-tightening.
If in doubt, it's a good idea to test the tank. Assemble the tank as you would normally, fill to above the top of the coil and then leave the tank to stand overnight (outside of the device).
- If there is no sign of any leakage, then the issue is almost certainly related to an error being made through use (see advice on how to avoid flooding above).
- If there are signs of leakage, it may indicate a physical fault with the tank:
- If the level of e-liquid in the tank drops to the feed holes on the coil, the issue is most likely related to the seal on the mouth tip.
- If the level drops to the top of the coil, the issue is most likely to do with the seal between the top of the coil and the bottom of the chimney of the tank.
- If the level drops to empty, or near empty, the issue is likely to do with the seal at the base of the coil.
LEAKING FROM THE HOUSING
- If a leak is coming from the glass window on the chamber itself, this is almost certainly a sign of a physical fault, such as a crack or break. A replacement tank will be required, but if your tank has been delivered in a damaged condition, please contact customer service.
Finally, it's important to know the difference between condensation and leaking. Vapour will naturally collect and form condensation, particularly if you tend to exhale onto/into the device. This will generally only ever be in small amounts, which shouldn't lead to noticeable leakage from the airflow of the tank. Simply drying this off periodically with a tissue should be enough to resolve the issue.
- The SERIES-S tank's are designed to be filled using bottles with a narrow nozzle. Avoid filling via wide nozzles as this risks e-liquid entering the central chimney and leaking down and out through the base of the tank.
- Do not overfill your SERIES-S tank - fill only to the top of the window. Filling past this point may cause liquid to leak down into the central chimney.